Yamaha R1 12-13 Japan

[ironpony]

Read from 2013 YZF-R1 Japan model.
New ECU(before immo registration) and Stock ECU(after immo registration)
Difference of the data is interesting

[ironpony]

We need open to read.
Write via connector.

[amissy]

that pinout used for this written?

[ironpony]

This is pinout for 09- YZF-R1.
Please do not redistribute!!

[amissy]

Ok.Thanks

[tipi65]

ironpony wrote:
> This is pinout for 09- YZF-R1.
> Please do not redistribute!!

[Interceptor]

Hi Tipi, you have Flash_tune software?

I was comparing some differences between their definitions and maps them. Have found the values ​​of conversions of some tables that are equal to the Flash-tune. values ​​of fuel, ignition, etc.. The break points of RPM is the same but have some diferences in TPS too. I did not find where to edit these break points in your xdf .... You seem to have taken advantage of the xdf Ducati.
Would help better develop this xdf. As you have much more experience than I believe that lowering the Flash-Tune software can take advantage of information available.
They unify the file in software of the electronic throttle (7055), and write the files one after another. But if we write 2 separate processors can generate 2 xdf.

[tipi65]

Interceptor wrote:
> Hi Tipi, you have Flash_tune software?
>
> I was comparing some differences between their definitions and maps them.
> Have found the values ​​of conversions of some tables that are equal to the
> Flash-tune. values ​​of fuel, ignition, etc.. The break points of RPM is
> the same but have some diferences in TPS too. I did not find where to edit
> these break points in your xdf .... You seem to have taken advantage of the
> xdf Ducati.
> Would help better develop this xdf. As you have much more experience than I
> believe that lowering the Flash-Tune software can take advantage of
> information available.
> They unify the file in software of the electronic throttle (7055), and
> write the files one after another. But if we write 2 separate processors
> can generate 2 xdf.

Yamaha YZF-R1 2013 actual fuel table RPM/TPS is 50 * 50 which use Flash Tune program, 48 * 33

Tuner Pro program equivalent to 48 * 33 (Number of Rows = 48), (Number of Columns = 33) and Minor Stride (bytes) = 36, etc..

[tipi65]

Interceptor wrote:
> Hi Tipi, you have Flash_tune software?
>
> I was comparing some differences between their definitions and maps them.
> Have found the values ​​of conversions of some tables that are equal to the
> Flash-tune. values ​​of fuel, ignition, etc.. The break points of RPM is
> the same but have some diferences in TPS too. I did not find where to edit
> these break points in your xdf .... You seem to have taken advantage of the
> xdf Ducati.
> Would help better develop this xdf. As you have much more experience than I
> believe that lowering the Flash-Tune software can take advantage of
> information available.
> They unify the file in software of the electronic throttle (7055), and
> write the files one after another. But if we write 2 separate processors
> can generate 2 xdf.

you mean?

[ravjeet]

can i directly use a FTD FT232R cable (5v) after programming it to flash the ECU
using FLASH-TUNE software .

[Interceptor]

Hi Ravjeet, no FTD cable with Flash-Tune software...this software only supports interface sold by them.

[ravjeet]

Interceptor wrote:
> Hi Ravjeet, no FTD cable with Flash-Tune software...this software only
> supports interface sold by them.
the software reads ft232r chip ID serial number (saved in 93c46 eeprom) which is registered at FT end once it does not match it gives message "device ID failure..."

[Interceptor]

exactly. I've tried to put the same programming that appears Mprog but they have a unique serial number

[Interceptor]

Hi Ironpony could you post the photo of the ECU cut out?
I have another ECU 4CB-8591A-60 here and would like to read the file

[PVTech]

ravjeet wrote:
> Interceptor wrote:
> > Hi Ravjeet, no FTD cable with Flash-Tune software...this software only
> > supports interface sold by them.
> the software reads ft232r chip ID serial number (saved in 93c46 eeprom) which is
> registered at FT end once it does not match it gives message "device ID
> failure..."

Or you can use a cracked version of the FlashTune software.

[ravjeet]

PVTech wrote:
> ravjeet wrote:
> > Interceptor wrote:
> > > Hi Ravjeet, no FTD cable with Flash-Tune software...this software only
> > > supports interface sold by them.
> > the software reads ft232r chip ID serial number (saved in 93c46 eeprom) which is
> > registered at FT end once it does not match it gives message "device ID
> > failure..."
>
> Or you can use a cracked version of the FlashTune software.
Do you have a copy of the crack software.
If yes give link for download

[Interceptor]

No, sorry, no have crack software FT

[ironpony]

Here.

[ravjeet]

we can read all the data from the genuine cable the problem is writing the serial number on to clone one . portion of the eeprom which has serial number is write protected or the software which FTDI used to read write ft232r chip does not have the function to write the entire eeprom .
i have heard that there are some linux based software where you can read image of original and copy it to clone .

Twice wrote:
> Nice cleaning
>
> Psyche, would it not be able to read eeprom from a genuine cable, then
> clone a regular one?
> Or is it protected in some way?